{"title":"Pallet Rack Dividers","description":"\u003cp\u003eOur pallet rack dividers keep loads apart and in place: snap-in wire mesh dividers split a wire deck into lanes, a mesh backstop stops cartons going off the back, U-dividers hold pallets off the uprights, and flue space protectors keep pallets out of the flue between back-to-back rows.\u003c\/p\u003e\n\n\u003ch2 class=\"h5\"\u003eWire rack dividers: lanes on a wire deck\u003c\/h2\u003e\n\u003cp\u003e\u003ca href=\"\/products\/wire-mesh-rack-dividers\"\u003eWire mesh rack dividers\u003c\/a\u003e snap into the decking wires with no tools and stand 12 in high. They run front to back, so choose by deck depth: the 34 in divider for 36 in deep decks, 40 in for 42 in decks, and 46 in for 48 in decks. You need one fewer divider than the number of lanes, and lanes do not have to be equal.\u003c\/p\u003e\n\n\u003ch2 class=\"h5\"\u003ePallet rack backstop\u003c\/h2\u003e\n\u003cp\u003eThe \u003ca href=\"\/products\/pallet-rack-backstop-divider\"\u003epallet rack backstop\u003c\/a\u003e is a 45 x 12 in wire mesh panel that hangs on loop hooks from the rear wire of a 46 in wide deck. Cartons pushed too far stop at the mesh instead of dropping into the flue or the aisle behind. It works with step and flared decks. Order one per deck: a 96 in bay with two 46 in decks takes two per level.\u003c\/p\u003e\n\n\u003ch2 class=\"h5\"\u003eU-dividers: transverse flue space\u003c\/h2\u003e\n\u003cp\u003e\u003ca href=\"\/products\/pallet-rack-u-dividers\"\u003ePallet rack U-dividers\u003c\/a\u003e bolt to the side of an upright and run front to back, holding each pallet 3 in off the frame so the gap between side-by-side pallets stays open. They come in 42 and 48 in depths, with two L-bolts and four Tek screws each, and fit teardrop uprights, not structural C-channel. They work with wire decking and open beams.\u003c\/p\u003e\n\n\u003ch2 class=\"h5\"\u003eFlue space protectors: longitudinal flue space\u003c\/h2\u003e\n\u003cp\u003e\u003ca href=\"\/products\/pallet-rack-flue-space-protectors\"\u003eFlue space protectors\u003c\/a\u003e bolt to the rear beam and stop pallets from being pushed into the flue between back-to-back rows. A single stop holds the pallet 3 in off the beam; double stops straddle the flue and fix it at 6 or 12 in. A slot fits over decking wire up to 2 gauge, so they mount over wire decks. Plan on two per pallet position per level.\u003c\/p\u003e\n\n\u003cp\u003eDividers and backstops fit our \u003ca href=\"\/collections\/pallet-rack-wire-decking\"\u003epallet rack wire decking\u003c\/a\u003e.\u003c\/p\u003e","products":[{"product_id":"pallet-rack-flue-space-protectors","title":"Pallet Rack Flue Space Protectors – Beam-Mounted Pallet Stops","description":"\u003ch2 class=\"h5\"\u003ePallet rack flue space protectors – beam-mounted pallet stops for NFPA 13 compliance\u003c\/h2\u003e\n\u003cp\u003e\u003cstrong\u003eKeep the flue open so the sprinklers can do their job.\u003c\/strong\u003e These flue space protectors bolt to the rear beam of a pallet rack and stop pallets from being pushed back into the longitudinal flue space between back-to-back rows. A fixed, visible flue lets overhead sprinklers reach the floor in a fire, which is what NFPA 13 and the International Building Code ask for, and a documented flue can help at insurance renewal. Four models cover a 3 in. single stop through an 18 in. double stop, all with pre-punched holes and self-drilling screws included.\u003c\/p\u003e\n\u003cp\u003eAlso called: rack flue space dividers, pallet stops for racking, flue space keepers, longitudinal flue dividers. If you have been searching under any of those names, this is the product.\u003c\/p\u003e\n\n\u003ch2 class=\"h5\"\u003eHow it works\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eControls pallet placement\u003c\/strong\u003e so a load cannot be pushed through into the flue behind the rack\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMeets NFPA 13 and IBC 2012\u003c\/strong\u003e flue space requirements when installed on both rows of a back-to-back run\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRigid box section, robotically welded\u003c\/strong\u003e for strength without adding weight to the beam\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInstalls in minutes\u003c\/strong\u003e with four pre-punched, countersunk holes; self-drilling screws are in the box\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eClears wire decking\u003c\/strong\u003e with an integral offset rib and a slot that fits over decking wire up to 2 gauge\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGrey powder coat\u003c\/strong\u003e finish\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2 class=\"h5\"\u003eSingle stop or double stop\u003c\/h2\u003e\n\u003cp\u003eA \u003cstrong\u003esingle stop\u003c\/strong\u003e mounts on one beam and holds the pallet 3 in. off the beam face. Use it where only one side of the flue needs a stop, or where the two rows are set at different heights. A \u003cstrong\u003edouble stop\u003c\/strong\u003e straddles the flue and holds both rows at once, fixing the gap at 6 in. or 12 in. depending on the model. The \u003cstrong\u003eheavy duty single stop\u003c\/strong\u003e adds a full-height gusset for racks that see hard forklift use.\u003c\/p\u003e\n\u003cdiv class=\"scrollable-table\"\u003e\n\u003ctable style=\"font-size:14px; white-space:nowrap\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth style=\"padding:8px\"\u003eModel\u003c\/th\u003e\n\u003cth style=\"padding:8px\"\u003eType\u003c\/th\u003e\n\u003cth style=\"padding:8px\"\u003eFlue created\u003c\/th\u003e\n\u003cth style=\"padding:8px\"\u003eWeight\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"padding:8px\"\u003eFG-SS-3\u003c\/td\u003e\n\u003ctd style=\"padding:8px\"\u003eSingle stop\u003c\/td\u003e\n\u003ctd style=\"padding:8px\"\u003e3 in. offset from the beam\u003c\/td\u003e\n\u003ctd style=\"padding:8px\"\u003e2.4 lb\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"padding:8px\"\u003eFG-SS-HD\u003c\/td\u003e\n\u003ctd style=\"padding:8px\"\u003eSingle stop, heavy duty\u003c\/td\u003e\n\u003ctd style=\"padding:8px\"\u003e3 in. offset from the beam\u003c\/td\u003e\n\u003ctd style=\"padding:8px\"\u003e1.3 lb\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"padding:8px\"\u003eFG-DS-12\u003c\/td\u003e\n\u003ctd style=\"padding:8px\"\u003eDouble stop, 12 in.\u003c\/td\u003e\n\u003ctd style=\"padding:8px\"\u003e6 in. flue between rows\u003c\/td\u003e\n\u003ctd style=\"padding:8px\"\u003e4.1 lb\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"padding:8px\"\u003eFG-DS-18\u003c\/td\u003e\n\u003ctd style=\"padding:8px\"\u003eDouble stop, 18 in.\u003c\/td\u003e\n\u003ctd style=\"padding:8px\"\u003e12 in. flue between rows\u003c\/td\u003e\n\u003ctd style=\"padding:8px\"\u003e5.7 lb\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\n\u003ch2 class=\"h5\"\u003eHow many do you need\u003c\/h2\u003e\n\u003cp\u003ePlan on two per pallet position per level, one near each end of the pallet, so the load cannot pivot past a single stop. A 96 in. bay holding two pallets takes four. For a full aisle, count pallet positions times levels times two. Ships from stock; larger runs ship on a pallet by freight.\u003c\/p\u003e\n\u003cp\u003eFitting out the racking? See our \u003ca href=\"\/products\/pallet-rack-wire-decking\"\u003epallet rack wire decking\u003c\/a\u003e, \u003ca href=\"\/products\/pallet-rack-u-dividers\"\u003eU-dividers for transverse flue space\u003c\/a\u003e and the full \u003ca href=\"\/collections\/rack-accessories\"\u003erack accessories range\u003c\/a\u003e.\u003c\/p\u003e\n\n\u003cdiv style=\"margin-top: 30px;\"\u003e\n\u003ch2 class=\"h5\"\u003eFrequently asked questions\u003c\/h2\u003e\n\u003cdiv itemscope itemtype=\"https:\/\/schema.org\/FAQPage\"\u003e\n\u003cdiv itemscope itemprop=\"mainEntity\" itemtype=\"https:\/\/schema.org\/Question\"\u003e\n\u003cp\u003e\u003cstrong itemprop=\"name\"\u003eWhat is longitudinal flue space and why does it matter?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cdiv itemscope itemprop=\"acceptedAnswer\" itemtype=\"https:\/\/schema.org\/Answer\"\u003e\u003cp itemprop=\"text\"\u003eIt is the gap between the backs of two pallet rack rows placed back to back. Fire codes require it to stay open so sprinkler water can reach the lower levels and the floor. Pallets pushed too far back close the gap, and flue space protectors stop that from happening.\u003c\/p\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv itemscope itemprop=\"mainEntity\" itemtype=\"https:\/\/schema.org\/Question\"\u003e\n\u003cp\u003e\u003cstrong itemprop=\"name\"\u003eSingle stop or double stop?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cdiv itemscope itemprop=\"acceptedAnswer\" itemtype=\"https:\/\/schema.org\/Answer\"\u003e\u003cp itemprop=\"text\"\u003eA double stop sets the flue between both rows in one piece and is the usual choice for back-to-back racking at matching heights. A single stop suits a single row against a wall, rows at different beam heights, or where you only need to hold one side.\u003c\/p\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv itemscope itemprop=\"mainEntity\" itemtype=\"https:\/\/schema.org\/Question\"\u003e\n\u003cp\u003e\u003cstrong itemprop=\"name\"\u003eDo they work with wire decking?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cdiv itemscope itemprop=\"acceptedAnswer\" itemtype=\"https:\/\/schema.org\/Answer\"\u003e\u003cp itemprop=\"text\"\u003eYes. The offset rib lifts the guard clear of the deck and the slot fits over decking wire up to 2 gauge, so they mount over standard wire decks without modification.\u003c\/p\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv itemscope itemprop=\"mainEntity\" itemtype=\"https:\/\/schema.org\/Question\"\u003e\n\u003cp\u003e\u003cstrong itemprop=\"name\"\u003eWhat do I need to install them?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cdiv itemscope itemprop=\"acceptedAnswer\" itemtype=\"https:\/\/schema.org\/Answer\"\u003e\u003cp itemprop=\"text\"\u003eA drill and the self-drilling screws that come in the box. The four holes are pre-punched and countersunk, so each guard goes on in a minute or two.\u003c\/p\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e","brand":"Dwixt","offers":[{"title":"Single Stop – 3 in. Offset","offer_id":50703705571614,"sku":"FG-SS-3","price":8.95,"currency_code":"USD","in_stock":true},{"title":"Single Stop – Heavy Duty","offer_id":50703705604382,"sku":"FG-SS-HD","price":11.95,"currency_code":"USD","in_stock":true},{"title":"Double Stop – 12 in. (6 in. Flue)","offer_id":50703705637150,"sku":"FG-DS-12","price":12.95,"currency_code":"USD","in_stock":true},{"title":"Double Stop – 18 in. (12 in. Flue)","offer_id":50703705669918,"sku":"FG-DS-18","price":16.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0814\/9031\/3502\/files\/Flue-Space-Protector-single.png?v=1793058916"},{"product_id":"pallet-rack-u-dividers","title":"Pallet Rack U-Dividers – Transverse Flue Space Spacers","description":"\u003ch2 class=\"h5\"\u003ePallet rack U-dividers – transverse flue space spacers that keep pallets off the uprights\u003c\/h2\u003e\n\u003cp\u003e\u003cstrong\u003eA fixed 3 in gap at every upright, without retraining the forklift drivers.\u003c\/strong\u003e These U-shaped steel dividers bolt to the side of a pallet rack upright and run front to back along the beam level, so a pallet cannot be pushed up against the frame. The result is a consistent transverse flue space on every level, which is what fire inspectors look for when they check that sprinkler water can reach the lower tiers. Mounting hardware is included and nothing is welded.\u003c\/p\u003e\n\u003cp\u003eAlso called: transverse flue spacers, pallet rack flue dividers, flue space dividers, U-divider rack spacers, pallet stops for racking, rack flue space spacers, pallet rack transverse stops. If you have been searching under any of those names, this is the product.\u003c\/p\u003e\n\u003cdiv style=\"display:flex;flex-wrap:wrap;gap:12px;margin:0 0 14px\"\u003e\n\u003cdiv style=\"flex:1 1 200px;min-width:0\"\u003e\n\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0814\/9031\/3502\/files\/Pallet_Rack_U-Dividers-42_-72dpi-2.png\" alt=\"42 in deep pallet rack U-divider with its mounting plate, product view\" loading=\"lazy\" style=\"width:100%;height:auto;display:block\"\u003e\u003cp style=\"margin:6px 0 0;font-size:14px;text-align:center\"\u003e42 in deep\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv style=\"flex:1 1 200px;min-width:0\"\u003e\n\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0814\/9031\/3502\/files\/Pallet_Rack_U-Dividers-1.jpg\" alt=\"U-divider mounted to a pallet rack upright, running front to back over wire decking\" loading=\"lazy\" style=\"width:100%;height:auto;display:block\"\u003e\u003cp style=\"margin:6px 0 0;font-size:14px;text-align:center\"\u003eBolts to the upright, runs front to back\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv style=\"flex:1 1 200px;min-width:0\"\u003e\n\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0814\/9031\/3502\/files\/Pallet_Rack_U-Dividers-4.jpg\" alt=\"U-divider mounting plate with the included L-bolts and Tek screws\" loading=\"lazy\" style=\"width:100%;height:auto;display:block\"\u003e\u003cp style=\"margin:6px 0 0;font-size:14px;text-align:center\"\u003eHardware included\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv style=\"flex:1 1 200px;min-width:0\"\u003e\n\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0814\/9031\/3502\/files\/Pallet_Rack_U-Dividers-10.jpg\" alt=\"Carton on wire decking held off the upright by a U-divider\" loading=\"lazy\" style=\"width:100%;height:auto;display:block\"\u003e\u003cp style=\"margin:6px 0 0;font-size:14px;text-align:center\"\u003eHolds the load 3 in off the frame\u003c\/p\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003ch2 class=\"h5\"\u003eHow it works\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e0.78 x 1.18 in steel tube\u003c\/strong\u003e, U-shaped, gray powder coat\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCreates a 3 in offset\u003c\/strong\u003e from the upright on the side it is mounted\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e42 or 48 in deep\u003c\/strong\u003e to match the frame depth\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHardware included\u003c\/strong\u003e: two L-bolts and four Tek screws per divider\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFits teardrop uprights\u003c\/strong\u003e, including Interlake and Mecalux styles, with or without side holes; not for structural C-channel uprights\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2 class=\"h5\"\u003eSizes\u003c\/h2\u003e\n\u003cdiv class=\"scrollable-table\"\u003e\n\u003ctable style=\"font-size:14px; white-space:nowrap\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth style=\"padding:8px\"\u003eModel\u003c\/th\u003e\n\u003cth style=\"padding:8px\"\u003eFits frame depth\u003c\/th\u003e\n\u003cth style=\"padding:8px\"\u003eOffset\u003c\/th\u003e\n\u003cth style=\"padding:8px\"\u003eTube\u003c\/th\u003e\n\u003cth style=\"padding:8px\"\u003eHardware included\u003c\/th\u003e\n\u003cth style=\"padding:8px\"\u003eWeight\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"padding:8px\"\u003e42 in\u003c\/td\u003e\n\u003ctd style=\"padding:8px\"\u003e42 in deep frames\u003c\/td\u003e\n\u003ctd style=\"padding:8px\"\u003e3 in\u003c\/td\u003e\n\u003ctd style=\"padding:8px\"\u003e0.78 x 1.18 in steel\u003c\/td\u003e\n\u003ctd style=\"padding:8px\"\u003e2 L-bolts, 4 Tek screws\u003c\/td\u003e\n\u003ctd style=\"padding:8px\"\u003e4.1 lb\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"padding:8px\"\u003e48 in\u003c\/td\u003e\n\u003ctd style=\"padding:8px\"\u003e48 in deep frames\u003c\/td\u003e\n\u003ctd style=\"padding:8px\"\u003e3 in\u003c\/td\u003e\n\u003ctd style=\"padding:8px\"\u003e0.78 x 1.18 in steel\u003c\/td\u003e\n\u003ctd style=\"padding:8px\"\u003e2 L-bolts, 4 Tek screws\u003c\/td\u003e\n\u003ctd style=\"padding:8px\"\u003e4.5 lb\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\u003ch2 class=\"h5\"\u003eHow many you need\u003c\/h2\u003e\n\u003cp\u003eOne divider per upright, per beam level, on each side where a pallet sits. A bay with pallets on both sides of an upright takes two per level at that upright. They work with \u003ca href=\"\/products\/pallet-rack-wire-decking\"\u003epallet rack wire decking\u003c\/a\u003e and with open beams, and pair with \u003ca href=\"\/products\/pallet-rack-flue-space-protectors\"\u003eflue space protectors\u003c\/a\u003e on the beams for the longitudinal flue. Browse the full \u003ca href=\"\/collections\/rack-accessories\"\u003erack accessories range\u003c\/a\u003e.\u003c\/p\u003e\n\u003cdiv style=\"margin-top: 30px;\"\u003e\n\u003ch2 class=\"h5\"\u003eFrequently asked questions\u003c\/h2\u003e\n\u003cdiv itemscope itemtype=\"https:\/\/schema.org\/FAQPage\"\u003e\n\u003cdiv itemscope itemprop=\"mainEntity\" itemtype=\"https:\/\/schema.org\/Question\"\u003e\n\u003cp\u003e\u003cstrong itemprop=\"name\"\u003eWhat is a transverse flue space?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cdiv itemscope itemprop=\"acceptedAnswer\" itemtype=\"https:\/\/schema.org\/Answer\"\u003e\u003cp itemprop=\"text\"\u003eIt is the gap between pallets that sit side by side across an upright, running front to back through the rack. Fire codes and insurers commonly require a consistent transverse flue so sprinkler water can reach the lower levels; the dimension required is set by your local code and your rack layout.\u003c\/p\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv itemscope itemprop=\"mainEntity\" itemtype=\"https:\/\/schema.org\/Question\"\u003e\n\u003cp\u003e\u003cstrong itemprop=\"name\"\u003eDoes it work with my uprights?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cdiv itemscope itemprop=\"acceptedAnswer\" itemtype=\"https:\/\/schema.org\/Answer\"\u003e\u003cp itemprop=\"text\"\u003eIt fits teardrop uprights, including Interlake and Mecalux styles, whether or not the upright has side holes. It does not fit structural C-channel uprights.\u003c\/p\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv itemscope itemprop=\"mainEntity\" itemtype=\"https:\/\/schema.org\/Question\"\u003e\n\u003cp\u003e\u003cstrong itemprop=\"name\"\u003eIs the hardware included?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cdiv itemscope itemprop=\"acceptedAnswer\" itemtype=\"https:\/\/schema.org\/Answer\"\u003e\u003cp itemprop=\"text\"\u003eYes. Each divider ships with two L-bolts and four self-drilling Tek screws for the mounting plate.\u003c\/p\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv itemscope itemprop=\"mainEntity\" itemtype=\"https:\/\/schema.org\/Question\"\u003e\n\u003cp\u003e\u003cstrong itemprop=\"name\"\u003eWhich depth do I order?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cdiv itemscope itemprop=\"acceptedAnswer\" itemtype=\"https:\/\/schema.org\/Answer\"\u003e\u003cp itemprop=\"text\"\u003eMatch the frame depth: 42 in dividers for 42 in deep frames, 48 in for 48 in deep. Measure from the front upright to the back upright.\u003c\/p\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv itemscope itemprop=\"mainEntity\" itemtype=\"https:\/\/schema.org\/Question\"\u003e\n\u003cp\u003e\u003cstrong itemprop=\"name\"\u003eDoes it damage the upright?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cdiv itemscope itemprop=\"acceptedAnswer\" itemtype=\"https:\/\/schema.org\/Answer\"\u003e\u003cp itemprop=\"text\"\u003eThe mounting plate bolts through the upright's existing side holes where they exist and uses the Tek screws where they do not. No welding and no drilling of the upright column.\u003c\/p\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e","brand":"Dwixt","offers":[{"title":"42 in. Deep","offer_id":50703705702686,"sku":"UD-42","price":14.95,"currency_code":"USD","in_stock":true},{"title":"48 in. Deep","offer_id":50703705735454,"sku":"UD-48","price":14.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0814\/9031\/3502\/files\/Pallet_Rack_U-Dividers-42_-72dpi-2.png?v=1775641388"},{"product_id":"wire-mesh-rack-dividers","title":"Pallet Rack Dividers – Wire Mesh Snap-In for Wire Decking","description":"\u003ch2 class=\"h5\"\u003ePallet rack dividers – wire mesh snap-in dividers for wire decking\u003c\/h2\u003e\n\u003cp\u003e\u003cstrong\u003eTurn one long shelf into lanes, without tools.\u003c\/strong\u003e These wire mesh dividers snap straight into the wire decking already on your pallet rack and stand 12 in. high to separate SKUs, create pick slots, or keep cartons from sliding into each other. Three widths match the common deck depths, so the divider runs front to back across the full deck. Snap in, load the lane, move it when the slotting changes.\u003c\/p\u003e\n\u003cp\u003eAlso called: pallet rack dividers, rack dividers, wire deck dividers, wire decking dividers, pallet rack shelf dividers, snap-in dividers, wire mesh shelf dividers, decking lane dividers. If you have been searching under any of those names, this is the product.\u003c\/p\u003e\n\n\u003ch2 class=\"h5\"\u003eWhy snap-in\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eClips into the deck wires\u003c\/strong\u003e; no brackets, no hardware, nothing to drill\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMoves in seconds\u003c\/strong\u003e when you re-slot a bay, so lanes follow the product mix\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e12 in. high mesh\u003c\/strong\u003e tall enough to hold cartons apart, open enough to see the label on the next lane\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWelded steel wire, powder coated\u003c\/strong\u003e to match the decking\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThree depths\u003c\/strong\u003e: 34, 40 and 46 in. to run the full depth of standard wire decks\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2 class=\"h5\"\u003ePick the width to match your deck depth\u003c\/h2\u003e\n\u003cp\u003eThe divider runs front to back, so choose the size that matches the \u003cstrong\u003edepth\u003c\/strong\u003e of your wire deck, not the beam length. A 36 in. deep deck takes the 34 in. divider, a 42 in. deck takes the 40 in., and a 48 in. deck takes the 46 in.\u003c\/p\u003e\n\u003cdiv class=\"scrollable-table\"\u003e\n\u003ctable style=\"font-size:14px; white-space:nowrap\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth style=\"padding:8px\"\u003ePart\u003c\/th\u003e\n\u003cth style=\"padding:8px\"\u003eDivider size (L × H)\u003c\/th\u003e\n\u003cth style=\"padding:8px\"\u003eFits deck depth\u003c\/th\u003e\n\u003cth style=\"padding:8px\"\u003eWeight\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"padding:8px\"\u003eWDD-34x12\u003c\/td\u003e\n\u003ctd style=\"padding:8px\"\u003e34 × 12 in.\u003c\/td\u003e\n\u003ctd style=\"padding:8px\"\u003e36 in.\u003c\/td\u003e\n\u003ctd style=\"padding:8px\"\u003e3.1 lb\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"padding:8px\"\u003eWDD-40x12\u003c\/td\u003e\n\u003ctd style=\"padding:8px\"\u003e40 × 12 in.\u003c\/td\u003e\n\u003ctd style=\"padding:8px\"\u003e42 in.\u003c\/td\u003e\n\u003ctd style=\"padding:8px\"\u003e3.6 lb\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"padding:8px\"\u003eWDD-46x12\u003c\/td\u003e\n\u003ctd style=\"padding:8px\"\u003e46 × 12 in.\u003c\/td\u003e\n\u003ctd style=\"padding:8px\"\u003e48 in.\u003c\/td\u003e\n\u003ctd style=\"padding:8px\"\u003e4.2 lb\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\u003cp\u003eOrder as many dividers as lanes you want, minus one, per deck. Ships from stock. Quantity pricing applies on larger orders, and a full aisle's worth goes out on a pallet by freight.\u003c\/p\u003e\n\u003cp\u003eThey fit our \u003ca href=\"\/products\/pallet-rack-wire-decking\"\u003epallet rack wire decking\u003c\/a\u003e; to guard the back of a deck instead, see the \u003ca href=\"\/products\/pallet-rack-backstop-divider\"\u003ewire mesh backstop\u003c\/a\u003e. Browse the full \u003ca href=\"\/collections\/rack-accessories\"\u003erack accessories range\u003c\/a\u003e.\u003c\/p\u003e\n\n\u003cdiv style=\"margin-top: 30px;\"\u003e\n\u003ch2 class=\"h5\"\u003eFrequently asked questions\u003c\/h2\u003e\n\u003cdiv itemscope itemtype=\"https:\/\/schema.org\/FAQPage\"\u003e\n\u003cdiv itemscope itemprop=\"mainEntity\" itemtype=\"https:\/\/schema.org\/Question\"\u003e\n\u003cp\u003e\u003cstrong itemprop=\"name\"\u003eWill they fit decking I already have?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cdiv itemscope itemprop=\"acceptedAnswer\" itemtype=\"https:\/\/schema.org\/Answer\"\u003e\u003cp itemprop=\"text\"\u003eThey are made for our wire decking, which has a 2.5 in. by 4 in. mesh. On another make of deck, check that the mesh is 2.5 in. by 4 in. before you order, or send us the deck details. Match the divider length to your deck depth and it clips in.\u003c\/p\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv itemscope itemprop=\"mainEntity\" itemtype=\"https:\/\/schema.org\/Question\"\u003e\n\u003cp\u003e\u003cstrong itemprop=\"name\"\u003eHow many do I need per shelf?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cdiv itemscope itemprop=\"acceptedAnswer\" itemtype=\"https:\/\/schema.org\/Answer\"\u003e\u003cp itemprop=\"text\"\u003eOne fewer than the number of lanes. Four lanes across a deck takes three dividers. They can sit anywhere along the deck, so lanes do not have to be equal widths.\u003c\/p\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv itemscope itemprop=\"mainEntity\" itemtype=\"https:\/\/schema.org\/Question\"\u003e\n\u003cp\u003e\u003cstrong itemprop=\"name\"\u003eCan I move them once they are in?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cdiv itemscope itemprop=\"acceptedAnswer\" itemtype=\"https:\/\/schema.org\/Answer\"\u003e\u003cp itemprop=\"text\"\u003eYes. Unclip, slide, clip. Nothing is fastened, so re-slotting a bay takes a minute rather than an afternoon.\u003c\/p\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e","brand":"Dwixt","offers":[{"title":"34 in. x 12 in.","offer_id":50703705768222,"sku":"WDD-34x12","price":7.9,"currency_code":"USD","in_stock":true},{"title":"40 in. x 12 in.","offer_id":50703705800990,"sku":"WDD-40x12","price":9.2,"currency_code":"USD","in_stock":true},{"title":"46 in. x 12 in.","offer_id":50703705833758,"sku":"WDD-46x12","price":10.45,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0814\/9031\/3502\/files\/Snap-In_Dividers-34_x12_7b69614d-329a-4d9b-9d17-fa63dc286ce3.jpg?v=1775770755"},{"product_id":"pallet-rack-backstop-divider","title":"Pallet Rack Backstop Divider – Wire Mesh Rear Guard","description":"\u003ch2 class=\"h5\"\u003ePallet rack backstop divider – wire mesh rear guard for wire decking\u003c\/h2\u003e\n\u003cp\u003e\u003cstrong\u003eStop cartons going off the back of the shelf.\u003c\/strong\u003e This 45 in. by 12 in. wire mesh backstop hangs from the rear edge of a wire deck on loop hooks and puts a barrier behind the load. Boxes and loose items that get pushed during put-away stop at the mesh instead of dropping into the flue or the aisle behind. It hangs on without tools and lifts off the same way if you re-slot the beams.\u003c\/p\u003e\n\u003cp\u003eAlso called: pallet rack backstop, rack backstop, wire deck backstop, pallet rack rear guard, wire mesh rear stop, shelf backstop for pallet racking, back stop for wire decking. If you have been searching under any of those names, this is the product.\u003c\/p\u003e\n\n\u003ch2 class=\"h5\"\u003eWhy fit a backstop\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eKeeps product on the shelf\u003c\/strong\u003e when a forklift pushes a pallet or a picker slides a carton too far\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eProtects the flue and the next aisle\u003c\/strong\u003e from falling stock, which is a safety issue as much as a breakage one\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLoop hook mounting\u003c\/strong\u003e hangs on the rear wire of the deck; no tools, no drilling, no hardware\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWelded steel wire mesh\u003c\/strong\u003e that stays open enough to see through\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSized for a 46 in. deck\u003c\/strong\u003e at 45 in. wide and 12 in. high, 4.8 lb\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2 class=\"h5\"\u003eSizing and quantity\u003c\/h2\u003e\n\u003cdiv class=\"scrollable-table\"\u003e\n\u003ctable style=\"font-size:14px; white-space:nowrap\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth style=\"padding:8px\"\u003ePart\u003c\/th\u003e\n\u003cth style=\"padding:8px\"\u003eSize (W × H)\u003c\/th\u003e\n\u003cth style=\"padding:8px\"\u003eFits deck width\u003c\/th\u003e\n\u003cth style=\"padding:8px\"\u003eMounting\u003c\/th\u003e\n\u003cth style=\"padding:8px\"\u003eWeight\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"padding:8px\"\u003eBSD-45x12\u003c\/td\u003e\n\u003ctd style=\"padding:8px\"\u003e45 × 12 in.\u003c\/td\u003e\n\u003ctd style=\"padding:8px\"\u003e46 in. wire decks\u003c\/td\u003e\n\u003ctd style=\"padding:8px\"\u003eLoop hook, tool-free\u003c\/td\u003e\n\u003ctd style=\"padding:8px\"\u003e4.8 lb\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\u003cp\u003eOrder one per deck along the run you want guarded. On a 96 in. bay with two 46 in. decks, that is two backstops per level. Ships from stock. Sets of a dozen or more go out on a pallet by freight; smaller quantities ship parcel.\u003c\/p\u003e\n\u003cp\u003eIt pairs with our \u003ca href=\"\/products\/pallet-rack-wire-decking\"\u003epallet rack wire decking\u003c\/a\u003e and the \u003ca href=\"\/products\/wire-mesh-rack-dividers\"\u003esnap-in dividers\u003c\/a\u003e that split a deck into lanes. Browse the full \u003ca href=\"\/collections\/rack-accessories\"\u003erack accessories range\u003c\/a\u003e.\u003c\/p\u003e\n\n\u003cdiv style=\"margin-top: 30px;\"\u003e\n\u003ch2 class=\"h5\"\u003eFrequently asked questions\u003c\/h2\u003e\n\u003cdiv itemscope itemtype=\"https:\/\/schema.org\/FAQPage\"\u003e\n\u003cdiv itemscope itemprop=\"mainEntity\" itemtype=\"https:\/\/schema.org\/Question\"\u003e\n\u003cp\u003e\u003cstrong itemprop=\"name\"\u003eWill it fit my wire decking?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cdiv itemscope itemprop=\"acceptedAnswer\" itemtype=\"https:\/\/schema.org\/Answer\"\u003e\u003cp itemprop=\"text\"\u003eIt is made for 46 in. wide wire decks, which is the standard width on 96 in. bays. The loop hooks catch the rear wire of the deck, so it works with step and flared channel decks alike.\u003c\/p\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv itemscope itemprop=\"mainEntity\" itemtype=\"https:\/\/schema.org\/Question\"\u003e\n\u003cp\u003e\u003cstrong itemprop=\"name\"\u003eIs this the same as a flue space protector?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cdiv itemscope itemprop=\"acceptedAnswer\" itemtype=\"https:\/\/schema.org\/Answer\"\u003e\u003cp itemprop=\"text\"\u003eNo. A flue space protector is a steel stop bolted to the beam that holds a pallet in place. A backstop is a mesh panel that catches loose cartons and small items. Many facilities fit both: flue space protectors for the pallets, backstops on hand-stacked levels.\u003c\/p\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cdiv itemscope itemprop=\"mainEntity\" itemtype=\"https:\/\/schema.org\/Question\"\u003e\n\u003cp\u003e\u003cstrong itemprop=\"name\"\u003eDoes it need tools to install?\u003c\/strong\u003e\u003c\/p\u003e\n\u003cdiv itemscope itemprop=\"acceptedAnswer\" itemtype=\"https:\/\/schema.org\/Answer\"\u003e\u003cp itemprop=\"text\"\u003eNo. Hook the loops over the rear edge of the deck and let it hang. It comes off the same way when you move the beams.\u003c\/p\u003e\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e","brand":"Dwixt","offers":[{"title":"45 in. L x 12 in. H | Loop Hook","offer_id":50703705866526,"sku":"BSD-45x12","price":12.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0814\/9031\/3502\/files\/Backstop_Divider-2-1.jpg?v=1776241231"}],"url":"https:\/\/dwixt.com\/collections\/pallet-rack-dividers.oembed","provider":"Dwixt","version":"1.0","type":"link"}